1-4). Run Guarding Vision software for the first time and register the administrator ( “Super User” ) account
Simply double click on the desktop icon for the first time***, and you will be prompted to make a username and password. This is the 3rd of the 4 username and password pairs that we have to deal with. This one is reasonably easy to understand: It is simple a username and password to let you use the guarding Vision Software on a particular computer.
If you remember to check , ( or leave it checked as it usually is by default ) , the Enable Auto-login box, then you will probably never need to concern yourself with this username and password pair ever again. But never the less, it does no harm to make a note of it somewhere, just in case it is ever needed again.
https://i.postimg.cc/BQfG7T81/Regist...-Aut-login.jpg
https://i.postimg.cc/G3yCj7pC/Regist...nmark-Star.jpg
So in the working example that I am using for this Blog this is the user name and password ( for the administrator account, ) required to log in to the Guarding Vision PC Client software on the PC that I am using for this worked example:
DocAElstein
Gaudy.!*
As far as I know, this user name and password is only held in the installed software and no where else. It is only required to open the installed software on a particular computer. So if you lose this user name and password, ( or as unfortunately does happen, the username and password is no longer recognised ), the simplest way around it is to de install the software and re install it. If you have a lot of time, an alternative is to contact Sannce Support who after a few weeks of correspondence may understand what you are asking and then guide you in a way to reset the user name and password ,
SANNCE Model: DN81BL I am using correct password. But it is no longer being accepted
https://support.sannce.com/hc/en-us/requests/1164553
Password Recovery.doc
https://app.box.com/s/9uszzgjf48t1fsbn5uhbo67y58bkakr2
61.5 KB
DN81BL I am using correct password. But it is no longer being accepted.doc
https://app.box.com/s/k9cc1zepe3nzk8atye167rhmiudonybd
202 KB
Sannce2PasswordResetCatastrohy.doc
https://app.box.com/s/85khysah0rhdpdfy9wan7ne7ubj92nn2
SADPTool.exe
https://app.box.com/s/0n78g9bh72ygtwu03acc6aothfeybwf0
36.3 MB
***Note: You may occasionally get various security or similar warnings, depending on your own various security settings, example:- https://i.postimg.cc/1z7LP6vP/Allow-Access.jpg
Usually these can be either be ignored and/ or simply agree to allow what the Guarding Vision Software to do what it is wanting to do
We now have the software running,
https://i.postimg.cc/MpHYJzYB/Initia...ine-device.jpg
( you may occasionally get an extra Help suggestion window showing https://i.postimg.cc/g27HY1MT/Extra-...Vision-use.jpg )
( The Super User name which we made on running the Guarding Vision software for the first time, ( - I chose _ DocAElstein _ ) , and that you would login with in subsequent opening, is shown in the top ribbon https://i.postimg.cc/c4JmZ3qD/Guardi...bbon-above.jpg )
Note also, that for the purposes of our working examples, we have , or should have, at all times, our DVR connected to the same router/modem as the computer that is running the Guarding Vision Software. This can be seen indicated in the On Devices in the bottom window.
https://i.postimg.cc/MpHYJzYB/Initia...ine-device.jpg
https://i.postimg.cc/jjcDv7pY/Initia...N-username.jpg
( You can also see in that shown Online Device, ( which is our DVR ) , the full long character Device Serial No. , https://i.postimg.cc/jjcDv7pY/Initia...N-username.jpg , also contains the effective 9 character user name serial number , SN , of our DVR, F53992124 , which we have discussed previously as one of the user names that we need to know about ).
( Note the use of the horizontal scroll bar to get at all the information:
https://i.postimg.cc/fWgThmLG/Online-Device-1-1.jpg https://i.postimg.cc/MH4Wb2N6/Online-Device-1-2.jpg https://i.postimg.cc/SRjSMNZ1/Online-Device-1-3.jpg )
If no Online Device is showing, then don’t go any further!!!
If our DVR is not shown, https://i.postimg.cc/nhKG5HkP/No-Online-device.jpg , then something has gone wrong, and before we go further we should check to see if we can cure this problem, https://excelfox.com/forum/showthrea...ll=1#post16054
All further setting up is concerned with Adding information to it to allow a PC to view in a similar way to which the monitor is used in the simplest use of the DVR
There are two ways to do this viewing via a PC,
(ii) 2a: Local LAN Access, ( making use of a typical modern internet Modem/ Router ‘s secondary LAN / central Server type function )
(iii) 2b: Cloud P2P Remote Access ( via the internet, ( will also need a typical modern internet Modem/ Router ) )
Conclusion/ Summary of what we see initially:
We are initially looking at Device Management , and by default a Device Type has been added automatically
So we are looking by default at the Device Management , and by default a Device Type has been added automatically, but at this stage there is nothing in it, so no actual device is being manages. But we can see that a device is available in the Online Device window. It is not essential to have a device showing in the On Line window in order to manage a device, but it is helpful if we want to manage that device, as the software will automatically recognise some details relating to that device, and this will mean that we may have to add less details ourselves when managing it.
( Managing is, in the first instance , mostly concerned with + Adding it. This so called with + Add basically means making it available for use in one way or another.
https://i.postimg.cc/MpHYJzYB/Initia...ine-device.jpg
https://i.postimg.cc/GtJvfKPs/Device-Manager.jpg
Device Manager.JPG
_ Device
________Device Managemant
_Device Type_
_#_Device__
Reply With Quote
Bookmarks